Car Diagnostic Tool Center

CK360 Easy Check Tester Identify VW MQB-A and MQB-B Key

uobdii | 05 June, 2019 22:56

CK360 Easy Check Remote Tester is a new Remote Key Tester for Frequency 315Mhz-868Mhz & Key Chip & Battery 3 in 1, also support Mercedes infrared key detection and Intelligent signal detection,best choice for technicians and repair shop.And here OBD2 will show you how to use it to detect VW MQB keys,include MQB-A and MQB-B.

Note:VVDI Mini Key Tool,Tango and Handy Baby 2 can not identify MQB-B key,but CK360 tester can

CK360 Tester Identify VW MQB-A and MQB-B Key:
Power on CK360 Easy Check tester, then select key identification menu and put the key on the coil.
Press power button

alt



Then CK360 will start key identification,please wait

alt



Now it show the key information:
49+ type
ID:C60A1E3F
MQB-B

alt



And  press back button,then put another key on the coil

alt



Press power button to start identification
Show the key information:
48 type
ID:0AB0E06A
MAB-A

alt



Done!

More detail about CK360 Remote Tester,please check here:
http://www.uobdii.com/wholesale/ck360-easy-check-remote-key-tester.html

How to Use SEC-E9 Machine Cut Tubular key?

uobdii | 23 May, 2019 23:18

In this article keycuttingmachine will show you how to use SEC-E9 machine to cut tubular key,hope it helps!

what is a tubular key?
Tubular keys are short keys with a hollow shaft most often used to open vending machines to retrieve coins and cash. A universal tubular key is one that is cut to fit a set of machines so that there is not a separate key for each machine.
tublar-key



How to do tubular key cutting?
First you should have a key cutting machine for tubular keys
Tubular keys can be cut with SEC-E9 key machine.

Second you need a tubular key clamp
tubular-key-clmap-sec-e9-key-machine

Source: http://www.uobdii.com/wholesale/tubular-key-clamps-for-sec-e9-key-cutting-machine.html
This is the tubular clamp tested ok with the SEC-E9 machine

Third, here is the tubular key list done by SEC-E9

Car Brand Model Year IC Card
AGA AGA 0-0 8647
AGA AGA 12 CSS2 0-0 8648
AGA AGA 42 0-0 8649
AGA AGA 39 0-0 8650
AGA AGA 37 0-0 8651
AGA AGA 0-0 8652
AGA AGA 0-0 8653
AGA AGA 0-0 8654
AGA AGA 0-0 8655
AGA AGA 0-0 7096
Beaver Beaver 0-0 6559
Bilma Bilma 0-0 8608
Bumil Bumil 0-0 6558
Chicago Chicago 0-0 6543
Dynaconsult Dynaconsult 0-0 6556
Fort Fort 0-0 6557
Fort Fort 0-0 6549
Lowe&Fletcher Lowe&Fletcher 0-0 6551
LYF LYF 0-0 8606
LYF LYF 0-0 8607
Meroni Meroni 0-0 6546
R.O.C. R.O.C 0-0 6550
R.O.C. R.O.C 0-0 6552
R.O.C. R.O.C 0-0 6553
Ronis Ronis 0-0 6554
SAG SAG 0-0 8656
Sentry Sentry 0-0 6555


Fourth, SEC-E9 and tubular key test report
Tubular key cutting done with SEC-E9 key cutting machine:
tubular-key-cutting-sec-e9-key-machine-1 tubular-key-cutting-sec-e9-key-machine-2 tubular-key-cutting-sec-e9-key-machine-3 tubular-key-cutting-sec-e9-key-machine-4 tubular-key-cutting-sec-e9-key-machine-5 tubular-key-cutting-sec-e9-key-machine-6 tubular-key-cutting-sec-e9-key-machine-7 tubular-key-cutting-sec-e9-key-machine-8
tubular-key-cutting-sec-e9-key-machine-9 tubular-key-cutting-sec-e9-key-machine-10 tubular-key-cutting-sec-e9-key-machine-11 tubular-key-cutting-sec-e9-key-machine-12 tubular-key-cutting-sec-e9-key-machine-13 tubular-key-cutting-sec-e9-key-machine-14 tubular-key-cutting-sec-e9-key-machine-15 tubular-key-cutting-sec-e9-key-machine-16 tubular-key-cutting-sec-e9-key-machine-17 tubular-key-cutting-sec-e9-key-machine-18
tubular-key-cutting-sec-e9-key-machine-18 tubular-key-cutting-sec-e9-key-machine-20 tubular-key-cutting-sec-e9-key-machine-21 tubular-key-cutting-sec-e9-key-machine-22 tubular-key-cutting-sec-e9-key-machine-23 tubular-key-cutting-sec-e9-key-machine-23 tubular-key-cutting-sec-e9-key-machine-25 tubular-key-cutting-sec-e9-key-machine-26 tubular-key-cutting-sec-e9-key-machine-27 tubular-key-cutting-sec-e9-key-machine-28
tubular-key-cutting-sec-e9-key-machine-29 tubular-key-cutting-sec-e9-key-machine-30 tubular-key-cutting-sec-e9-key-machine-31 tubular-key-cutting-sec-e9-key-machine-32 tubular-key-cutting-sec-e9-key-machine-33 tubular-key-cutting-sec-e9-key-machine-34 tubular-key-cutting-sec-e9-key-machine-35 tubular-key-cutting-sec-e9-key-machine-36 tubular-key-cutting-sec-e9-key-machine-37 tubular-key-cutting-sec-e9-key-machine-38
source: http://www.uobdii.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html

CGDI MB Benz W164 All Key Lost Programming EIS Data Collection

uobdii | 07 May, 2019 22:52

For traditional method for Benz EIS data collection,it will take you about several hours.It is inefficient,so here I share the guide on how to solve Benz EIS data collect inefficiently,here I take Benz W164 as example.
Benz W164 All Key Lost Programming EIS Data Collection (1)

Preparations:
CGDI Benz Prog
CGDI Benz AC Adapter

And for the Benz key programming you can reference this video guide:
https://youtu.be/IFZk4ytJusI


Procedures:
Run CGDI MB Monster software and select “Wiring Diagram”,then check the wire harness diagram
Benz W164 All Key Lost Programming EIS Data Collection (2)
Follow the wire diagram to build wire harness connection
Benz W164 All Key Lost Programming EIS Data Collection (3) Benz W164 All Key Lost Programming EIS Data Collection (4)

Select “EIS” option at left menu bar,then click “Read EIS data”
Benz W164 All Key Lost Programming EIS Data Collection (5)
After reading EIS data,click “Compute Password” at left menu bar
Chose “Copy key without key”,and click “Collect Data”.
Then select “Platform mode(Quick collect)” and click “OK” to start data collection.Note:Here need CGDI MB AC Adapter
Benz W164 All Key Lost Programming EIS Data Collection (6)
Benz W164 All Key Lost Programming EIS Data Collection (7)
Please insert the simulation key within 1 minutes,if you have inserted,please pull out and try again.
(Please turn the quick collect adapter switch to the Platform position.Turn the key to ignition ON position)
Benz W164 All Key Lost Programming EIS Data Collection (8)
It will take you about 6 minutes to collect data,please wait…
Note:By traditional method,you need spend hours
Benz W164 All Key Lost Programming EIS Data Collection (9)
After data collection completing,save the data on your laptop
Benz W164 All Key Lost Programming EIS Data Collection (10)
Then click “Upload Data” button to upload the data you save just now for password caculation
Benz W164 All Key Lost Programming EIS Data Collection (11)
Upload data successfully,please click “Query Reqults” buttons to query
Benz W164 All Key Lost Programming EIS Data Collection (12)
Calculation successfully
Benz W164 All Key Lost Programming EIS Data Collection (13)
Done!
http://cgdi.over-blog.com/

How to Connect Yanhua ACDP to Your Mobile Phone

uobdii | 30 April, 2019 00:31

Here comes the guide on how to connect  Yanhua ACDP to mobile phone.If is necessary for fresh man on first time user to get it.And for more article about Yanhua Mini,please check here:Yanhua Mini ACDP Tech


Here is a Youtube guide on how to use Yanhua Mini ACDP:
https://youtu.be/xXt2jlAOLuc 

Procedures:

1Open the Bluetooth and connect the WiFi

alt




2Open the ACDP on your phone and click setting as the following icon;Click “Initial use settings”

alt



3Following the directions: press and hold the “SET” button on the ACDP device for about 7s till the device’s buzzer sounds, then release the “SET” button. Then click “Next”;

alt



4Choose the device;

alt



5Enter the password of WiFi, then click “Start configuration”;

alt



6Bond the device;

alt

7Bonded successful as the following.

alt

 

 Article from Yanhua Mini Tech Blog:

Launch X431 CRP429C Smart & Manual Diagnostic Guide

uobdii | 17 April, 2019 23:15

Here obd2 share the guide on how to use Launch X431 CRP429C smart & manual diagnosis function.

Launch CRP429C Smart Diagnosis:
After connection, turn the ignition key on and the system enters auto-detect mode.
Note: To detect more and accurate VINs, a stable network connection is highly recommended for this function.
CAUTION: Don’t connect or disconnect any test equipment with ignition on or engine running.
A. Once the system successfully obtains the VIN (Vehicle Identification Number) information of the currently identified vehicle, it will continue scanning the vehicle systems. After the scanning is complete, a diagnostic report will be automatically generated and sent to your email box (if bound).
B. If the tool failed to access the VIN information, the screen will display as below:

alt



Input the VIN, and tap “OK”, the system will automatically identify the vehicle
model. If the vehicle VIN is successfully decoded, it will perform autodiagnosis
until a diagnostic report is automatically output. Otherwise it will
enter manual diagnosis mode.
Notes:
• The most recognizable location for this number is in the top left corner on the
vehicle’s dashboard. Other locations include the driver’s door or post, and the
firewall under the hood.
• In general, vehicle identification numbers are standardized - all contain 17
characters. VIN characters may be capital letters A through Z and numbers
1 through 0; however, the letters I, O and Q are never used in order to avoid
mistakes of misreading. No signs or spaces are allowed in the VIN.

Launch CRP429C Manual Diagnosis
If the tool can not obtain the VIN information, you can also perform vehicle
diagnosis manually. In this mode, you need to execute the menu-driven
command and then follow the on-screen instruction to proceed.
Notes:
• Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your CRP429C.
• For vehicles manufactured by different vendors, it is possible that it has different
diagnostic menus. For details, please follow the instructions on the screen to proceed.Refer to the flowchart illustrated as below to diagnose a vehicle manually:

alt



Take Demo as an example to demonstrate how to diagnose a vehicle.
1). Select diagnostic software version: Tap the “DEMO” to go to Step 2.

alt



2). Select test item: Select the desired test item to proceed.

alt


More information about Launch CRP429C,please check here:
http://www.uobdii.com/wholesale/launch-x431-crp429c-auto-diagnostic-tool.html

How to Use CGDI MB Prog to Read/Clear/Write Mercedes Benz NEC chips

uobdii | 29 March, 2019 23:41

This mini post show a test report on CGDI Mercedes programmer read,clear,write a NEC chip.And for more CGDI MB programmer test case,please check here:CGDI Benz Test Cases

Note:Download CGDI software here:CGDI BMW BENZ Software Download

Procedures:
step 1 dismantle the key and desolder the NEC chip
cgdi-mb-nec-chip-1
step 2 clean the pcb and nec chip before welding back on the board
cgdi-mb-nec-chip-2
step 3 identify the nec chip and weld onto the nec board
cgdi-mb-nec-chip-3
step 4 select the nec adapter and corresponding chip type
cgdi-mb-nec-chip-3
step 5 read key/chip
cgdi-mb-nec-chip-5
step 6 reset
cgdi-mb-nec-chip-6 cgdi-mb-nec-chip-7

step 7 if you have key files already, open/write
cgdi-mb-nec-chip-8 cgdi-mb-nec-chip-9 cgdi-mb-nec-chip-10

success!
step 8 read key/chip to confirm the success of key writing
cgdi-mb-nec-chip-11 cgdi-mb-nec-chip-12

Done!

CGDI MB is able to read and write NEC chips!

VVDI MB 4.7.0 New Version Update Information

uobdii | 07 March, 2019 23:11

Here is newest VVDI MB Programmer Tool 4.7.0 Update information,and you can download and update it to this version.

alt




Released notes:
1. This update no need update the firmware
2.Password calculation for ALL KEY LOST:
Support W164/W251(-2009), W221 calculate password when all key lost:
a. Support W164/W251(-2009) get key password with slow method (All KEY LOST, 25minutes-1.5hour)
b. Support W221 get key password with VVDIMB Power Adapter (All KEY LOST, no need re-insert IR, 15minutes)
c. Support W221 get key password with slow method (All KEY LOST, 25minutes-1.5hour)

EIS (FBS3) list: all keys lost
VVDIMB support all key lost EIS type (FBS3) as listed below
W166, W197, W212, W218, W246,W172, W204, W207,W216
W164, W251 (-2009)
W164, W251 (2009-)
W169, W209, W211
W202, W208, W210
W203, W463, W639
W639(2009-)W906
W221

VVDI MB car list: all keys lost
VVDI MERCEDES version 4.7.0 supports the following models all keys lost  and can program new keys without soldering:
W166 W197 W212 W218 W246
W172 W204 W207
W216
W164 W251 (-2009)
W164 W251 (2009-)
W221
W169 W209 W211
W202 W208 W210 W203 W463 W639
W639 (2009-)
W906
Test: Tested successfully by one of our customers
VVDI MB V4.7.0 confirmed MB W221 AKL All Keys Lost tested successfully by one of a prominent customers in Libya
This perhaps could be the 1st W221 In the world ? to get a set of working keys without having EIS replaced

UOBDII Official Blog All rights reserved VVDI MB 4.7.0 download with FULL list of EIS (FBS3) all keys lost

BMW E/F Scanner Read BMW CAS1-CAS3+ ISN Code Operation Guide

uobdii | 13 February, 2019 21:52

Here I want to share the guide on how to use BMW E/F scanner II to read out BMW CAS1-CAS3+ ISN code.

And for more information please visit BMW E/F Scanner  blog

alt


BMW E/F Scanner Interface:
V2018.12 BMW E/F Scanner II Full Version (Recommend)
2013.07V E/F SCANNER For BMW

The BMW Explorer program has a possibility of reading a code of synchronization of ISN (all versions of CAS1 CAS2 CAS3 CAS3+).
Go to the CAS control unit, “Additional functions”, “Reading ISN”
In the opened window ISN will be displayed.
If the machine is equipped with the EWS3 system where 2 bytes of the constant part and the change are used, it will be displayed in the window 2 bytes of ISN DME (the upper 3 windows will be empty), if necessary they can be changed.

If the machine uses the EWS4 system, then 16 bytes of constant synchronization are used and there is no variable part.
Also after 2006, CAS3 uses an anti-theft code for EGS
If there is an EWS3 system in the car, then this code is the same with the engine control unit, if the machine already has an EWS4 system, then EGS uses separate 2 bytes
The program is in place of the engine ISN, it will display the gearbox code .. as in the picture below
How to Use BMW E/F Scanner Read BMW ISN Code for CAS1-3+
UOBDII All rights reserved How to Use BMW E/F Scanner Read BMW ISN Code

How to Solve Hyundai & Kia GDS VCI ?CRC Error?

uobdii | 23 January, 2019 21:59

Recently,some customers ask the solution for their Hyundai & Kia GDS VCI "CRC" Error.So here UOBD2 share the procedure to solve this problem.

And for more auto diagnostic tool

Trouble Descriptions:
Installing Hyundai GDS (Global Diagnostic System) software on Win 7 laptop, when come to Hyundai master setup wizard installation step, the system reported an error:

“CRC error: The file C:/gvci/ocx/install/dotnetfx-eng.exe doesn’t match the file in the setup’s.cab file. The medium from which you are running the setup may be corrupted; contact your software vendor.”

Error screen

alt

Possible reason:
1. Operating system issue
2. Improper installation steps
3. Software damaged

Solution:
Please follow the video or blog guide (below) to install GDS program. If the Hyundai master setup can be well installed, but others cannot, then send the specific file name that cannot be installed to obd365 customer service. We will resend the file.

We recommend users to choose U-Disk format software rather than CD software. U-Disk format GDS V2.14 software HDD is easier to install.


blog.uobdii.com

FVDI 2015 2016 Device Locked Solution

uobdii | 09 January, 2019 21:57

Here UOBD2 give out the solution to solve FVDI 2015 2016 locked error,hope it helps!
And check here for newest FVDI 2018

http://www.yanhuaacdp.com/
The symptoms show as below:
1.FVDI device can not work
2.Green led light of FVDI unit is off
3 .Red-green led of software dongle(red dongle) blink.

Here UOBD2 engineer give the solution:
1.If your FVDI device has not yet been locked,please update the Quick Loader to v7.0 as soon as possible.After updating the Quick Loader,you can run the FVDI correctly.



Quick Loader v7.0 Download:
https://mega.nz/#!WAglGaTB!t-JvU38sWLrw4CEmpidu0TZzkNbhGGsLweAbYOrb-Yw
How to Solve FVDI 2015 2016 Locked Error-1
2.If you FVDI has been locked,you need to send the main unit to FLY factory for repairing.And you need to pay $50 for unlock service and shipping cost.

3.And if you would like to send the device back to factory for repairing,you would like to choose pay for extra money to get the Newest 2018 version FVDI (never locked version)
FVDI 2018 2015 FVID2 Installation Step by Step Guide
And there is the last choice to repair this problem by yourself,but you need to try it at all your risk.We dont take responsibility for the result!!!
This solution is share on DK forum by the member.

1.) FVDI V2015 or higher with softdog versions:
If the pc cannot detecting any fvdi’s then the LPC1788 processor was erased ( the Quickloader v6.3 will erase the LPC processor ).
always erasing are the following two address: 0x00000000-0x00047FFF or 0x00000000-0x0007FFFF
How to Solve FVDI 2015 2016 Locked Error-2 How to Solve FVDI 2015 2016 Locked Error-3

(click to enlarge)
After the FVDI died because there are no has a BOOT sector and the some firmware rows.
2.) if you cannot bought any FVDI’s from FLY Company, then the pc will go to internet then always erasing all FVDI LPC processors by FLY server !!!!!
3.) I solved all algorithms to fvdi firmware encrypting/decrypting and now i looking the 8bytes key to v2015 version.
How to Solve FVDI 2015 2016 Locked Error-4

How to renew/ virgin used Toyota smart key by CN900 MINI?

uobdii | 27 December, 2018 21:50

Do you know it’s easy to reuse an old matched Toyota smart key? Below you will know: How to renew/ reprogram/ virgin a used Toyota smart key by CN900 MINI key programmer?

Smart CN900 Mini Tech

STEPS: CN900 MINI renew Toyota smart key with 74 chip
Power on CN900 MINI, it will show main menu including “Read & Copy”, “Test Frequency”, “Special” and “Setup”.

alt


Choose “Special” function then “Smart Key”.

alt


Follow the instruction: Put the used Toyota smart key into the transponder area (the coil as picture).

alt


Click “Clear Byte” and “Yes” to confirm.

alt


Wait a minute and don’t move the key, the original key data will be erased.

alt


In this way, you use CN900 MINI to renew and virgin an old used Toyota smart key successfully! Now a new working Toyota smart key with blank key chip is ready! 

Yanhua Mini ACDP Programmer

Source: How to renew/ virgin used Toyota smart key by CN900 MINI?

How to Update & Active/Add Tokens for Autek IKey820 Programmer

uobdii | 16 December, 2018 22:11

This article show a guide on how to update,active/add tokens for Autek IKey820 Programmer.


Preparations:
1Autek IKey820 Key Programmer
2PC with Win10/Win8/Win7/XP
3USB cable
Autek IKey820 Update Tool V1.5

Install Update Tool on Your PC
If the update tool “Autek IKey820 Update Tool V1.2” is already installed on your PC before,just skip this step.If not,you need to install it.
Run “Autek Ikey820 Update Tool v1.5.exe”

alt



Note:The update v1.2 need installation,but for v1.5 you can run it directly
Autek IKey820 Update Tool contains three parts including update,active and message from top to bottom

alt




Update Autek IKey820 Key Programmer:
Take the following steps to update Autek IKey820 device:
1.Connect IKey820 to PC via USB cable
2.Open Autek IKey820 update tool on your PC(Your PC need to connect on Internet)
3.Select the device in list and input the SN (usually completed automatically)
4.Click Update button to start updating,wait until the updating completed.


There is something you need to notice in each step.
1) The device should display “USB SD DISK MODE” when connected to PC through USB cable, if not, please unplug the USB cable and plug again. Do not unplug the USB cable or exit from USB SD DISK MODE.
2) If AUTEK IKEY 820 Update Tool is not installed, please install it first, see detail in chapter 2.
3) The DISK and SN should display automatically if the device is connected to PC. If the DISK has no device to select, please unplug the USB cable and plug again. If the DISK has been selected, but SN is empty, please unplug the USB cable and plug again. If it’s still the same, please input SN yourself. The SN should start with “A-”.
4) It may take several minutes to update, it depends on the speed of your internet.

If there is any problem, it will display on message area, check according to the message and try again.

Here are the pages for updating. The SN is just an example, you should use your own SN.
Check SN and DISK before updating.

alt



Wait until update successfully

alt



Update successfully

alt




Activate/Add Token 
Activation means add tokens to your device. If your device runs out of tokens or you want to increase the number of tokens, you can use AUTEK IKey 820 Update Tool to increase tokens.
Take the following steps to activate AUTEK IKey820 device:
1) Supply power to the AUTEK IKey820 device through USB/12V DC adapter/OBD.
2) Go to the ACTIVATE menu, you will see a page with steps to activate your device and the REQ CODE which is need in AUTEK IKey820 Update Tool to get the ANS CODE.
3) Open AUTEK IKey820 Update Tool in your PC.
4) Input the REQ CODE to the AUTEK IKey820 Update Tool and click ACTIVATE button, then you will get the ANS CODE
5) Press OK button on the device and there display the page to input ANS CODE
6) Input the ANS CODE you get in the AUTEK IKEey820 Update Tool. There are two different
7) Press OK button and the page will show the result, SUCCESS or FAILED.
8) You can check your tokens in the ABOUT menu if you activate your device successfully.

Here are the pictures to activate the device. All the SNREQ CODE and ANS CODE are examples, just ignore them.
Select the ACTIVE menu

alt



The ACTIVE page

alt


Open Autek IKey820 Update Tool and input the REQ CODE

alt


Get the ANS CODE

alt



Input ANS Code

alt


Confirm the ANS CODE you input

alt


Succeed means active successfully

alt


Check the token in About page

alt



 Article from:http://blog.uobdii.com/autek-ikey820-updating-and-activation-guide/

How to Use Digimaster 3 to Decode Mercedes Benz Audio?

uobdii | 04 December, 2018 21:51

When the vehicle audio was power off because of battery damage, the audio will start the anti-theft system automatically-UOBDII.com remind you. So here I want to share you how to use Yanhua Digimaster 3 to decode audio for Mercedes Benz.

Digimaster III can calculate the audio code out or initialize it, as the following picture shows, Digimaster 3 has the function of ” Audio decoding” , after click it, you will find it supports decoding audio for Alfa, Audi, Benz, BMW, Ford, gm, Honda, Lexus, mazda, Mitsubishi, Peugeot, Porsche, Renault, Toyota, Volvo, Volkswagen and more.

alt



2. Audio Code Management
Step 1: Select Benz to decode, and de-solder the corresponding chip according to the software prompts. Click “Next” to begin decoding.

alt



Step 2: remember the code in the pop-up dialogue box, click “Next”, the code was written in the chip.

alt

Step 3: Solder the chip back to the board, and then use this new code to decode the audio.

3 Address Code
These models only need to short-circuit some welding spot to reset the code, the software will give a specific method.

Odometer Correction

UOBDII All rights reserved Mercedes Benz audio decoding using Digimaster III

How to Solve OBDSTAR X300M Security Verification Failed Trouble

uobdii | 29 November, 2018 21:49

When used the OBDStar X300M to do odometer correction function on OPEL Astra 2010, it come out the error “Security Verification Failed”,
obdstar-x300m-tested-opel-astra-2x300m-secturity-verification-failed-error-1 obdstar-x300m-tested-opel-astra-security-verification-failed-3
How to solve the X300M security verification failure ?
When it fails to communicate or program, please operate as below:
1.Connecting x300m — Starting it-Pressing option-Pressing Data Logging-Pressing on-Pressing ESC – Back to the main menu.
2.When it fails to program, power off the machine please.
3.Pull our TF card where there is a LOG file.
4.Send us the LOG file and the engineer would study the data and figure out the reason.
From OBDSTAR Tools Technical Official Blog, post Solution to OBDStar X300M Security Verification Failure

VVDI Prog and Xprog is Best Choice for Fresh Man

uobdii | 22 November, 2018 21:56

If you are a beginner of VVDI Programmer, you don’t need the adapters, if you need to read eeproms, get a second programmer like Xprog 5.55.

And for many auto locksmiths,it is important to choose a suitable programmer,here i put it here:
http://www.uobdii.com/wholesale/auto-key-programmer/

Why another programmer? Is not good with eep?
Xprog is cheaper then a vvdiprog adapter.
vvdi prog is good for reading proccesors.
Some have had problems reading eeproms.
This might be solved now that there is a adapter.
If your vvdiprog fails, at any reading or programming, you will have a backup.
It also helps as a confirmation to solve some reading writing problems.
All my collegues have at least few laptops, w7 32 w7 64 and xp.
And xprog, upa, tl866, willem, orange5
Xprog, is a great tool, and comes with many adapters.
Some even sell a xprog clamp adapter, to make i even more handy to use.
The picture posted, is 17euro adapter to use on xprog.
xprog-ecu-programmer-clip-adapter-1


UOBDII All rights reserved Why vvdi prog + Xprog is needed for a beginner?

1 2 3 4 5 6 7 8 9  Next»
 
Provided by Multiblog.net - easy blogging platform
P0wered by L1fe7ype - De51gn by Ba1earWe6