Car Diagnostic Tool Center

How to Update & Active/Add Tokens for Autek IKey820 Programmer

uobdii | 16 December, 2018 22:11

This article show a guide on how to update,active/add tokens for Autek IKey820 Programmer.


Preparations:
1Autek IKey820 Key Programmer
2PC with Win10/Win8/Win7/XP
3USB cable
Autek IKey820 Update Tool V1.5

Install Update Tool on Your PC
If the update tool “Autek IKey820 Update Tool V1.2” is already installed on your PC before,just skip this step.If not,you need to install it.
Run “Autek Ikey820 Update Tool v1.5.exe”

alt



Note:The update v1.2 need installation,but for v1.5 you can run it directly
Autek IKey820 Update Tool contains three parts including update,active and message from top to bottom

alt




Update Autek IKey820 Key Programmer:
Take the following steps to update Autek IKey820 device:
1.Connect IKey820 to PC via USB cable
2.Open Autek IKey820 update tool on your PC(Your PC need to connect on Internet)
3.Select the device in list and input the SN (usually completed automatically)
4.Click Update button to start updating,wait until the updating completed.


There is something you need to notice in each step.
1) The device should display “USB SD DISK MODE” when connected to PC through USB cable, if not, please unplug the USB cable and plug again. Do not unplug the USB cable or exit from USB SD DISK MODE.
2) If AUTEK IKEY 820 Update Tool is not installed, please install it first, see detail in chapter 2.
3) The DISK and SN should display automatically if the device is connected to PC. If the DISK has no device to select, please unplug the USB cable and plug again. If the DISK has been selected, but SN is empty, please unplug the USB cable and plug again. If it’s still the same, please input SN yourself. The SN should start with “A-”.
4) It may take several minutes to update, it depends on the speed of your internet.

If there is any problem, it will display on message area, check according to the message and try again.

Here are the pages for updating. The SN is just an example, you should use your own SN.
Check SN and DISK before updating.

alt



Wait until update successfully

alt



Update successfully

alt




Activate/Add Token 
Activation means add tokens to your device. If your device runs out of tokens or you want to increase the number of tokens, you can use AUTEK IKey 820 Update Tool to increase tokens.
Take the following steps to activate AUTEK IKey820 device:
1) Supply power to the AUTEK IKey820 device through USB/12V DC adapter/OBD.
2) Go to the ACTIVATE menu, you will see a page with steps to activate your device and the REQ CODE which is need in AUTEK IKey820 Update Tool to get the ANS CODE.
3) Open AUTEK IKey820 Update Tool in your PC.
4) Input the REQ CODE to the AUTEK IKey820 Update Tool and click ACTIVATE button, then you will get the ANS CODE
5) Press OK button on the device and there display the page to input ANS CODE
6) Input the ANS CODE you get in the AUTEK IKEey820 Update Tool. There are two different
7) Press OK button and the page will show the result, SUCCESS or FAILED.
8) You can check your tokens in the ABOUT menu if you activate your device successfully.

Here are the pictures to activate the device. All the SNREQ CODE and ANS CODE are examples, just ignore them.
Select the ACTIVE menu

alt



The ACTIVE page

alt


Open Autek IKey820 Update Tool and input the REQ CODE

alt


Get the ANS CODE

alt



Input ANS Code

alt


Confirm the ANS CODE you input

alt


Succeed means active successfully

alt


Check the token in About page

alt



 Article from:http://blog.uobdii.com/autek-ikey820-updating-and-activation-guide/

Comments

Add comment

 This is the ReCaptcha Plugin for Lifetype

 
Provided by Multiblog.net - easy blogging platform
P0wered by L1fe7ype - De51gn by Ba1earWe6