Car Diagnostic Tool Center

how to use OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32

uobdii | 25 May, 2018 05:09

Recently,OBDSTAR engineer share video guide on how to use OBDSTAR H100 program dealer key for VW Polo 2013 NEC 24C32.Here OBDSTAR share it for customers.

OBDSTAR X300 PAD2

Procedures:
Connect OBDSTEAR H110 to vehicle by OBD port.
Power on the device.
Select “VEHICLE”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (1)
Select “IMMOBILISER”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (2)
Select”VW/AUDI/SKODA/SEAT”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (3)
Select “VW/ADUI/SKODA/SEAT V33.25”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (4)
Select “VW”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (5)
Read security code
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (6)
4 Generation Immo
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (7)
NEC+24C32 ICM
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (8)
Make Ordinary Dealer Key.
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (9)
Reading data …
Please connect RFID with diagnostic device
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (10)
Please put the new key in RFID adapter.
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (11) OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (12)

Reading data …
Generating dealer key…
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (13)
When you find the LED light on the RFID adapter flash on 3 time,the OBDSTAR H110 Programmer will prompt you “Make Dealer key success”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (14)

Attention Please:
If you find the warning massage with “Communication Breakdown”.Please check below conditions:
1.Ignition Switch is turned on
2.Mainline is connected
3.Battery has power
4.Is Equipped with this ….
OBDSTAR X300 DP PAD Programmer

From OBDSTAR Tools Technical Official Blog, post OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32

CGDI BMW program key on BMW CAS4 /CAS 4+ all key lost

uobdii | 18 May, 2018 05:20

Have BMW MSV80 and looking for a key programmer to add new key for BMW CAS1/CAS2/CAS3/CAS3+ and match key for CAS4 /CAS 4+ when all key lost, you must use CGDI Prog BMW MSV80 key programmer.
cgdi-pro-bmw-msv80-key-programmer-1

Attach one table which show CGDI Prog functions, workable models and working time
cgdi-pro-workable list-01

As you can see, CGDI Prog BMW MSV80 key programmer has these capabilities:

  1. 1.BMW CAS1/CAS2/CAS3/CAS3+/key increasing matching, KEY all lost matching, CAS computer replace,CAS3+/P4X above version can directly downgrade by OBD in 5 minus 100% safety.

2.BMW CAS4/CAS4+/Support key matching, support key all lost matching.
3.Support BMW key inspection, can check key what status in.
4.Support BMW engine computer DME replacement.
5.Support BMW MSV80/MSD80/MSD85/series OBD read ISN code (no need to split computer when matching key) Exclusively support in Domestic
6.Support BMW Key unlock.

Moreover, CGDI Prog can perform:
1.Update in real time, products updated in zero cycle time, support model added in real time.
2.BMW CAS3/CAS3+Data repair–support change replace and split CAS computer, BMW MSV80/MSV80.0/MSD80/MSD80.0/MSD85/engine change computer, ISN code reading and writing.
3.Equipment security greatly enhanced, the hardware anti-crack, anti-software copy.

CGDI MB Benz

How to use CGDI Prog BMW MSV80 key programmer?
Method 1: can directly read ISN code in the car, please ensure the car voltage is 12V and above, it directly connects OBD to operate, takes about 5 minus.
Method 2: can directly disassemble engine computer (DME) to operate, follow the below guide to connect the line:
cgdi-pro-bmw-msv80-key-programmer-1
cgdi-pro-bmw-msv80-key-programmer-pic-4 
CGDI Shop

Top 5 Auto Key Cutting Machine for Automotive Locksmith

uobdii | 16 May, 2018 04:40

Here are 5 auto automotive key cutting machine for auto locksmith.

iKeycutter Condor XC-Mini

alt

 

 
1. Built-in Database, can easily find key information
2. Support Multi-languages: Portuguese/Spanish/French/Germany/Czech/Arabic/Turkish/Dutch/Polish/Bulgarian/Norway/Slovakia/Italian/English/Chinese
(Turkish and Russian will be released in the future)
The way to change language:
Please provide us with the serial number and wait us to authorize the language you want, then you can use the Update Tool to choose the language.
3. Update Online Lifetime
4. 3-Axis Precision Ball Screw Transmission
5. Cross Rail
6. All Aluminum Machine Body
7. Single machine with both Tracer/Cutter
8. Standardly include clamps M1/M2, M3 needs to buy alone

9. Support Sided/Track/Dimple/Tibbe keys
10. Some Dimple/Tibbe keys need optional clamps

src:http://www.uobdii.com/wholesale/ikeycutter-condor-xc-mini.html




SEC-E9 CNC Automated Key Cutting Machine

alt

1. Can directly search key bitting number by key code for some keys. No need to search from Instacode
2. Can cut a new key by bitting number, when original key is lost.
3. Support 10 languages including English, Spanish,French,German,Italian,Korean,Portuguese,Russian, Turkish, Czech.
4. Can cut veritcal milling, flat milling, internal milling and external milling.
5. Can cut automobile keys,motorcycle keys ,dimple keys, tubular keys, and single-sided standard keys.
6. Can cut Tibbe keys and LDV keys
7. Auxiliary Clamp is available
8. CE Approved
9. Work on Car, Truck, Motorcycle, House Key, Dimple & Tubular Keys
10. Update Online for Free


Automatic V8/X6 Key Cutting Machine with Dust Cover

alt

1. It can be used with the key keyless condition, lightweight and portable, battery-powered DC electrical impulse is very suitable to go out to work.
2. Mainly used have the key with keyless lost data with the key. When there is a key, simply follow the steps to enter the number or read key teeth tooth number, you can make a new key. When a key is lost, just follow the prompts, enter the appropriate number of head lock, you can make a new key.
3. It is also can according your requirement ,through the intelligent choice to make key tooth depth. Easy to use, suitable for a variety of automotive lock key.
4. USB cable data transfer, compatible with a variety of key database
5. Quick change guide pin and cutter
6. Modular design, easy maintenance (Quick Change Module)
7. English menu. Configuration:
one PCS English manual ( Electronic files ).
one PCS 2.5mm dedicated mills. two PCS Dedicated probe 2. Spare belt.
one PCS USB data cable and one set Electrical impulse
8. Multi-language support: English ,Italian,Portuguese,Spanish


368A Key Cutting Duplicated Machine

alt

1. Multi functional practical machine, equipped with horizontal feeding movable handle
2. Multifunctional steel fixture, can copy various hollowness type,wave type,cylindrical key and key for multi lock and composite bead keys and some car keys,such as BMW,HONDA,Volkswagen car keys
3. Fixture with dark key duplication service pitch line and cylinder type key assembly function (multifunctional clamp)
4. With hardened ball bearing slide mechanism.
 
JINGJI L2 Vertical Key Cutting Machine

alt


1. Callibration system indicated by LED light make sprecisely cutting
2. Cutter speed regulated to 8500rpm
3. Straight line slide carriage makes cutting smooth and effortless
4. Cutting depth locking mechanism makes accurate result
5. Rmovable jaw with two grooves makes cutting more convenient
6. Vertical movement backwards makes more space to install clamp
7. Spring loaded tracer point make sperfect depth alignment
8. Structured with aluminum alloyed casting technique
9. Armrest support makes the cutting forward stable and smooth
CGDI Shop

More info about key cutting machine,please visit:Key cutting Machine

OBDSTAR X300M Adjust Mileage for Hyundai Mistra

uobdii | 15 May, 2018 05:26

OBDSTAR X300M is ideal mileage adjustment tool for Hyundai Mistra 2017, because it complete new kilometer adjustment via OBD without dismantling the cluster.

Related Products
OBDSTAR X300 DP PAD Tablet
OBDSTAR X300 Pro3 Key Master

As you can see on the Hyundai Mistra 2017 dashboard, the old value is 20685KM.
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-01
I will connect OBDSTAR X300M to the Hyundai via OBD2 cable, power on it and go to the menu “Cluster calibration”, you can see the car makes option, choose “Hyundai”.
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-02

Hyundai V30.70.
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-03

Loading…
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-04

Initializing…
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-05

Authorizing…
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-06

As you can see, this is Hyundai supported list, choose ” Mistra”.
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-07 obdstar-x300m-to-adjust-hyundai-mistra-kilometer-08
Select “Kilometer”.
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-09

Communicating…
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-10

X300M reads out the old mileage: 20685 kilometer, then you can see the dashboard info.
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-11 obdstar-x300m-to-adjust-hyundai-mistra-kilometer-12

Input the new value 10650KM
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-13 obdstar-x300m-to-adjust-hyundai-mistra-kilometer-14

Communicating…
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-15

Adjustment complete. You can see the dashboard display 10650KM.
obdstar-x300m-to-adjust-hyundai-mistra-kilometer-16 obdstar-x300m-to-adjust-hyundai-mistra-kilometer-17

Done!
It’s amazing to use OBDSTAR X300M to adjust mileage on Hyundai, it’s so easy even the user is not professional. I highly recommend it, everyone can own one because it is cheap about 300USD.

Like:
http://www.obdstartool.com/wholesale/obdstar-x300m-special-for-odometer-adjustment-and-obdii.html
$319 free shipping.

From OBDSTAR, post How to use OBDSTAR X300M to adjust Hyundai Mistra kilometer?

Xhorse VVDI2, VVDI Prog, VVDI MB tool Reviews

uobdii | 09 May, 2018 05:53

Xhorse electronics vvdi reviews here, incl xhorse the best:
VVDI mercedes review
VVDI Prog programmer review
VVDI2 programmer review
CGDIShop

VVDI MB Tool review

– cost-effective and powerful
vvdi mb can renew elv without soldering the nec while the other should sold out and not make via obd2, vvdi mb can renew EIS no need token even its bga eis , while others cannot , with small budget can program bga key with 6 minutes while with others you need 5 thousands dollars to do , more over for w204 all key lost no body in the world can do it while they are working on it with vvdi
xhorse-vvdi-mb-bga-tool-new-1
– 204 all keys lost ok
For 204 all keys lost one solution is to buy eis with key tested and ok

– W203 password calculation via IR
I read pass W203 IR OK

– W203 W220 read password ok
W203: EIS/EZS A203.545.05.08 – MCU ??? -read PSW IR – OK
W203: EIS/EZS A203.545.05.08 – MCU 1J35D – read PSW – OK
W220: EIS/EZS A215.545.02.08 – MCU ??? -read PSW IR – OK
– support older ESL
old ESL(motorola) are supported read through K-line yet……look in ESL menu, there are some possibility…

for me are all older ESL from 202, 203, 208,209,201,211 and so…then when in the adapter are socket for the 28-pin HC05E6 motorola, then are this supported too…
the emulator is too for all this OLD type of ESL…

– renew this namber 7G tronic 003 446 0310
Can renew this namber 7G tronic 003 446 0310
i have renewed 10 pcs of this part number, all success

– made a key to W203
I have made a key for W203.
Works great but the remote controle opens only the drivers door.

– Exchange W204 ESL without renew EIS
Exchange W204 ESL without renew EIS. In ESL Tools, write EIS with password(Select Auto clear TP and personalized) tested and work ok

– w204 w207 w212 all key lost work
All key lost:
W204 work
W207 work
W212 work


VVDI Prog Review

– read/write Fiat 9s12dg256b mcu without problem
Yesterday i read/write mcu 9s12dg256b from fiat bcm with vvdi Prog WITHOUT Problem
vvdi-prog-1
VVDI Prog secured very well
I work’s on opel astra h cim with hc912 mcu,
ford dashboard hc912, and with hc908az60
secured very well.

– 080dowq erasing works perfect
Now I tried 080dowq erasing, and it works perfect.

– R/W ok with CIM Opel Astra H
3L40K – Read ID (0113) ok, Rean EEP (ok) Read Flash (ok)
1L59W- Read ID (0115) ok, Read EEP (NOT) Read Flash (NOT).

Ps. 3L40K – Just that flash is smaller than It should be.
Read-it with smok, and You will understand what I am saying.

– 50/50 chance to Porsche BCM
I have tried to read Porsche BCM with 9S12 5M48H dated 2013 MCU but could not do it because VVDI Prog did not detected chip ID. Always get ID: FFFF
While Porsche BCM with MCU 9S12 2M25J dated 2014 have read without problems

– 209 flash ok
I received the vvdi prog and tested eis
209 with st12 eeprom flash ok

– vvdi prog read ok with W221
for w221 ism with ST10F269 read by vvdi prog OK with micromax diagram
for write it didn’t erase automatically you have to erase it before, then all OK .

–  ok with D70F3571
vvdi prog 4.5.1 D70F3571 read ok

– no issues with BSI 307 2002
BSI 307 2002 912DG128 – 3K91D
EEP (read and write) – OK
FLASh 4.000Mhz (read and write) -OK — Orange5 clone (DO NOT write flash)
Identical files Vvdi prog and Orange5, same EEP and FLASH.
Incircuit BSI photo of Orange5.

– vvdiprog + eeprom adapter without issues
works fine with eeprom adapter
does not work with test clip tried to different ones,
maybe i should try other one, if there is any higher quality,
or maybe because of cable length it doesnot work

– good at EZS, CAS2, CAS3, CAS3+ …
this programmer can read write EZS, cas2, cas3, cas3+, read other motorolas safe without any problems or damages

– work OK on BMW CAS4 F10 2014
Today tested: CAS4 with Motorola 1N35H mask from F10 2014!
d/p-flash BACKUP – ok
Crack chip security – ok
read/write p/d-flash – ok
Locked – ok
Works without heating the chip. Only removed 4 elements from the board, and after operations resoldered them back.
i have desoldered 4 elements from the board: transistor, capacitator, resistor and cristal/quartz.


– vvdi prog not working?:
– VVDI PROG CANNOT READ 68HC805 FOR IMMO MAZDA 323

– It cannot read hcx05 at all.

– Cannot support read pin code for psa and old chrysler



Xhorse VVDI2 review

VVDI2 BMW:

– CAS1 bmw read eeprom by obd
i did yesterday CAS1 bmw read eeprom by obd and got key info and cutting code
vvdi2-key-programmer-1
– bmw ews direct by obd
vvdi2 bmw can make key in bmw ews direct by obd or need read ews dump by programmer then make key

– program new keys to bmw e90 2008 USA
i have a vvdi2 with vag and bmw authroization
have to programmed new keys in bmw (bmw e90 2008 USA year), without keyless go
in original key inside transponder pcf7953 315mhz
My hint for you: Chinese keys work only transponder but remote need to remove cas and do it on bench on tango or xhorse vvdi, but obd method need always original for better chance chip is 7945 or 7953 which is 46 family good luck

– support MED17/EDC17 dump tool
Xhorse vvdi2 v1.2.1 adds support for MED17/EDC17 dump tool, support clone ECU(Menu->Special Function->MED17/EDC17 dump tool)
But sadly only work for Condor key cutting machine users
my vvdi 2 is full not basic.but function for edc17 only for condor cutter user.no for all vvdi2 full user
vvdi mb bga have the token system, if you have condor cutter 1 token in 1 day for free if you don’t have you need pay
it is different


VVDI2 AUDI:

– do Control head on A6
Vvdi2 able to do Control head on A6
need Transponder Sokymat Crypto 8E – Audi ID8E precoded by Component Security.
If you want to add remote key: 4F0837220AK, 4F0837220R, 4F0 837 220 – and others.

– key learn for Audi A4 RB8 crypto (2004+)
VVDI2 key learn procedure for Audi A4 RB8 crypto (2004+) option:
Just read the pin and cs from ecu.
Make backup from cluster, and the cluster configuration.
Then make a dealer key, and learn it with pin.

Audi A7 2012 km done
Audi A7 2012 km done by reading config by obd then read eeprom by Programmer ——– ok!

– Audi S8 spare key job done
Did one Audi S8 done successfully, spare key job

– add keys to AUdi a4 2009 BCM2
AUdi a4 2009 BCM2 key added successfully in 2 minuts.

Audi Q5 add keys, read bcm2
I did Audi Q5 add key ok, read BCM2 by OBD ok, read BCM2 by bdm ok.
Passat B6 all key lost by eep ok.

Audi A3 8P 434 not working
Remote programmer test remote for Audi A3 8P 434, not working.
Not file for Golf 5 434.
Test remote generator Ibiza 6J “1k0 …. N” 434 working.

Audi A4 2008 not working
VAG remote key adaptation does not connect to many old cars but usually works fine with newer “dealer keys”. However, Audi A4 2008 did not connect to car (BCM or BFM). Key programming ok.
On a side note: A4 2008 do not have BCM, models 2009 + has BCM.


VVDI 2 & others:

– Peugeot 308 2008 BSI JC pin extracted
Peugeot 308 2008 BSI JC pin extracted OK. Key learn failed – first key OK, second key failed. Tried several times. Job finished with other device.

Passat B6 read code and add keys
Passat B6 read Code from confort module (95320) & added key ok!

– 0D69J file identified
BENZ a class 0D69J file identified ok, but write transponder not work

– Passat B7 failed
Passat B7 Read Code from confort (95320) & add key by obd ——— Failed, (i made by transponder tool option)
VVDI Key Tool

UOBDII All rights reserved Xhorse vvdi review of VVDI2, VVDI Prog, VVDI MB

Review on OBDSTAR X300 PRO3 Key Master

uobdii | 08 May, 2018 04:36

At that time I was hesitated to purchase OBDATAR X300 PRO3 or SKP-900 key programmer to program smart key for my Ford car. Now I'm glad for my choice to X300 PRO3, of course I do not have bad reviews on SKP-900, it is also a powerful and professional diagnostic tool, but I think X300 PRO3 more suitable for me.
OBDSTAR H108
obdstar-x300-pro3-key-master 


X300 PRO3 key master by OBDSTAR Company features with the immobilizer key programming function of SKP900, as well as new function such as Odometer adjustment, EEPROM/PIC and OBDII. This car key programmer I got from uobdii.com charged US$485, compared to skp-900 who would charge more expensive. And as far as I know uobdii 9th Anniversary Free Shipping is under the way, at the outset I took a little money for Shipping.
Well, why do I say that this key programming tool suitable for me? I use X300 pro3 to successfully correct odometer of my car for odometer value is high enough to put up with. Several days ago, my best friend borrowed to reset oil service, he said it was easy to operate and he wanted to buy one too. I am happy my OBDATAR X300 PRO3 helps to solve his trouble. I have owned this hand-held key programmer for 3 months, and become a little expert with it.
Here I also share with you how to update software for OBDSTAR X300 Pro3 Key Master
At first, you should download the update tool and diagnostic software on www.obdstar.com, then double click the application to install.
Step1: When Update Tool installation complete, click the update tool icon on the desktop to start it.
Step2: Then click source menu, choose the program you want to update, click confirm
Step3: click and select all the software then click “update”
Step4: wait for several minutes until updating finished.
Final Statement: these are all my experience when using X300 Pro3, there is no suspicion of selling, please purchase according to your own needs and wishes.
OBDSTAR X300M
www.obdstartool.com

 
Provided by Multiblog.net - easy blogging platform
P0wered by L1fe7ype - De51gn by Ba1earWe6